Mise à jour R-Link2 update from 2.2.X to 3.3.16.961 with Android Auto

[rgmaster3]

Mise à jour R-Link2 2.2.X vers 3.3.16.961 avec Android Auto




Vidéo:
https://mega.nz/#!rSZWxIjS!nkVO4lfilkKj ... zy48iD73MI

Section téléchargement, voir en bas de cette page

Tutoriel pdf avec liens de téléchargement et vidéo de configuration

Télécharger-Download.txt

Autres liens de téléchargement

Télécharger-Download.txt

[Umberto64]

Ciao. Ho ha provato caricare la versione 3.3.16. Ho aspettato con il motore acceso Piu di 1/2 ora il mio R-Link 2 se non di più acceso. Ho provato FARE ha un reset, se non il mio Accende Più. Posso tariffa Anche con Qualcosa DDT4ALL? Se Non Posso tariffa nulla prima di Andare alla Renault Posso cancellare lo storico dell'aggiornamento? Il Kajar Ho Che E in Garanzia e non vorrei Che mi facessero Pagare l'R-Link Nuovo.

[rgmaster3]

mi scusi, ho usato la traduzione di google ma non ho capito niente
excuse me, I used the google translation but I didn't understand anything

[Umberto64]

In fact, the automatic translation is not clear. I write in English hoping to be clearer.
Hello. I tried to load version 3.3.16. The update has started but after a few seconds R-Link 2 has shut down. I waited more than half an hour while the engine was running. Since then R-Link 2 has not turned on. I tried to restore it by holding the power button and disconnecting the battery, but R-Link 2 seems dead. I have an OBD interface. Can I do something with DDT4ALL? Unfortunately the car is under warranty (long-term rental). If I can't restore R-Link 2, can I at least cancel the memory of the update attempts?

[Umberto64]

In fact, the automatic translation is not clear. I write in English hoping to be clearer.
Hello. I tried to load version 3.3.16. The update has started but after a few seconds R-Link 2 has shut down. I waited more than half an hour while the engine was running. Since then R-Link 2 has not turned on. I tried to restore it by holding the power button and disconnecting the battery, but R-Link 2 seems dead. I have an OBD interface. Can I do something with DDT4ALL? Unfortunately the car is under warranty (long-term rental). If I can't restore R-Link 2, can I at least cancel the memory of the update attempts?

[rgmaster3]

In fact, the automatic translation is not clear. I write in English hoping to be clearer.
Hello. I tried to load version 3.3.16. The update has started but after a few seconds R-Link 2 has shut down. I waited more than half an hour while the engine was running. Since then R-Link 2 has not turned on. I tried to restore it by holding the power button and disconnecting the battery, but R-Link 2 seems dead. I have an OBD interface. Can I do something with DDT4ALL? Unfortunately the car is under warranty (long-term rental). If I can't restore R-Link 2, can I at least cancel the memory of the update attempts?

yes now I understand well
since your R-Link 2 is stopped because of an update, so it is useless to repair with DDT4all or others, the failure and in the internal disks of your r-link, in this forum we find all type of hardware repair but only on media nav and not rlink.
if the car and under warranty, possible your your Renault dealer will change it by a new one, hoping

[edjenew]

hello,
i have now 2.2.19.800 is it possible to update with this file to 3.3?
or will my rlink2 crash

[rgmaster3]

nothing to fear is an update that works without a problem

[edjenew]

and after that i can activate AA and android/? i have a megane estate IV
hope it will work

[boulevai]

bonsoir c'est pas gagné avec les fonctions cachées sur le rlink mais il parait que avec ddt4all sa fonctionne , moi je n'arrive pas a l'installer sur winxp
bye